A New Solution for Chemical Fiber Dyeing
2019-07-18 Read[34]

Compared with cotton, chemical fiber is more sensitive. Crease mark, scratch and snagging will easily occur in this type of fabric. Due to the protection from water flow, Jet-dyeing machine was one of the best dyeing solutions for fabrics containing chemical fiber before.


Water flow protection means high water consumption. In the past, this is acceptable. However, nowadays more and more textile countries focus on environmental protection such as China, Vietnam, Indonesia and Bangladesh, etc. Not only water treatment should be set up, but also Gov. requests dyeing companies to use green energy like gas. Cost is getting high and keep using Jet-dyeing machine is no longer the best solution any more.


Therefore, with the support for green industry, a new dyeing solution for chemical fiber, which comes with low consumption and good fabric quality, should follow up.


In this subject, Texpro did a deep study. Now in the market of China and the textile countries nearby, a new solution from Texpro call Multi-flow dyeing technology is getting hot.


Texpro, which you can also call Texpro group, located in Foshan, the knitting base of South China, is the founder of Multi-flow dyeing machines and its technology.


First, we will talk about dyeing quality, and then we go to consumption part. Without good quality, consumption is meaningless.


So, why Multi-flow dyeing technology can be the solution of chemical fiber dyeing?


The key is the design of nozzles.


From the picture, you can see that before winch house, there is a set of water nozzle. After winch house there is an air nozzle.


The function of water nozzle is only to spurt dyeing liquid out.


The function of air nozzle is to drive the fabric, meanwhile detwisting fabric from rope form.


When fabric detwists and runs faster, crease marks are getting less.

For operator, to reduce circle time is easy. Only by increasing the power of air blower and the speed of winch house, fabric can run faster and safer. Even fabric can run without water.


Multi-flow technology can reduce crease mark, but if we talk about control crease mark’s appearance, we need to control the whole processing such as pre-heat setting and knitting.


Next we focus on consumption.


Two parts will affect water consumption during processing. One is liquor ratio; another is the efficiency of rinsing.


Liquor ratio can be 1:3.5 to 1:5 for Multi-flow dyeing machine. Compared with Jet dyeing, which is 1:8 to 1:13, Multi-flow dyeing machine has great advantages in reducing water consumption.


Meanwhile, steam consumption and chemical consumption will also be lower. The cost of this two parts take more than 30% of the dyeing cost, and dyeing house can save lots of cost from it.


Rinsing takes most of the water consumption from the whole processing. When Rinsing, clear water comes out from water nozzle and cleans fabric. After that, fabric goes up to the winch house, water gets dirty and goes down to bottom of machine. Then the water can be drain out if too dirty, or again go back to nozzle if still useful for rinsing.


In this logic, rinsing efficiency is high and water consumption is less. Fabric after washing will be separated from dirty water, and then it goes to backside of chamber.


Power consumption is controlled by two factors.


One is the installed power and running power. Taking the example of Texpro Multi-flow dyeing machine, 2 chambers 600 kg capacity, the total installed power is 37 kW. Running power is from 13 kW to 16 kW. Compared with same capacity of Jet dyeing machine and Air flow dyeing machine, power consumption of Texpro Multi-flow dyeing is the lowest.


Another one is total processing time.


Texpro Multi-flow dyeing has second circulation system and high efficiency rinsing system. These can reduce dosing time and rinsing time. Nevertheless, here we would like to talk more about right first time dyeing. Right first time dyeing means when dyeing process is done, the color we check is matched with our request for the first time. There is no need for redyeing and no more power consumption. More than thousands of Texpro Multi-flow running in the world and customers are satisfied with this. Less color difference from batch to batch and high right first time dyeing rate.


From the introduction above, we can see that Texpro Multi-flow dyeing is one of the best solutions for chemical fiber dyeing. This technology is getting hot and dyeing houses in China, Vietnam, Cambodia, Indonesia, Pakistan, Taiwan and many other places are widely using this. We are happy to see now we have a green dyeing solution for the world.


There are still more potentials for this machine waiting for you to explore and welcome to contact with us for more discussion.


Pre: 233 1
Next: null
Back
ABOUT TEXPRO
Under Texpro group, there are two companies: one is Son-tech Precision Machinery Co., Ltd and another one is Texpro & Stentex Machinery Technology Co., Ltd. Its history can be traced back to 1997. For many years, we’ve tightly focused on the business philosophy of "Making Sophisticated Dyeing and Finishing Machinery is Our Profession", adhered to the path of quality and service innovation for sustainable development, given full play to Texpro's competitive advantages of design, manufacture and process, and tried to develop a business characterized by high efficiency, energy saving and environmental protection.
MORE
Follow Us on WeChat

Copyright (C) Guangdong Sanji Klangz Mechanical Technology Co., Ltd. E-mail: sales@texpro-group.com 粤 ICP 备 13041936 号 -1 | Address: No. 69-2, A District, Da Tang garden, Guangdong Foshan City, Sanshui District, central science and Technology Industrial Zone| Phone: +86-757-88303372